What Auditors Check in First Article Inspection


Three production runs were compared for dimensional tolerance last spring. Variation stayed inside 12 microns once we changed the moulding temperature.

Building First Article Inspection Into Manufacturing

Operator training for first article inspection stations includes a written qualification exam. New operators run 50 test assemblies under supervision before working alone.

What Industry Experts Say

We keep our production lines running on documented procedures rather than individual habits. That is why output quality stays consistent even when staff rotate between shifts.

Chen Wei, Production Manager, tbphp

Yield and Rework Data

Calibration records for first article inspection instruments are kept current. Audit teams check these first, so the lab reviews the list monthly.

Key Numbers to Compare

Stage Duration Key Activity Deliverable
Quote 1-2 weeks RFQ + doc review Quotation
Sample 2-3 weeks Sampling + testing Sample report
Audit 1 week Factory visit Audit report
Production 4-8 weeks Manufacturing Shipment

Specification Setting

First article inspection for first article inspection covers every drawing dimension. The report is kept with the lot record and shown to auditors.

Mold cavity position explains most of the variation we see in first article inspection. Cavities near the gate fill slightly differently, and balancing them cut our dimensional reject rate from 4.1 percent to 1.8 percent.

Our lab tests first article inspection using a cycle counter that runs samples to 500,000 strokes. Needles that hold alignment past 300,000 cycles almost never fail in field data, so that number became our internal gate.

Cleanroom conditions affect first article inspection assembly. Particle counts are logged daily, and the room is recertified every six months.

Dimensional measurement for first article inspection uses a calibrated profile projector. The operator records five points per cartridge, and the data feeds our SPC charts in real time.

We validate first article inspection after sterilization, not before. EO exposure can soften some adhesives, so assembly properties are confirmed on sterilized samples.

We document first article inspection defects by category every week. The top three codes consume about 70 percent of rework, which keeps our improvement effort focused.

Defect codes for first article inspection are reviewed weekly. The top three codes drive the improvement plan, and each has an owner and a deadline.

Mold cavity balance is the largest single factor in first article inspection consistency. Balancing our four cavity mold cut dimensional rejection from 4.1 percent to 1.8 percent.

Sterilization validation for first article inspection covers three consecutive production lots. The validation report lists chamber load, cycle parameters, and biological indicator results for each run.

Sterilization validation for first article inspection covers three consecutive production lots. The validation report lists chamber load, cycle parameters, and biological indicator results for each run.

We retain first article inspection samples from every lot for one year. Re-testing a retained sample answers most customer quality questions.

Mold cavity position explains most of the variation we see in first article inspection. Cavities near the gate fill slightly differently, and balancing them cut our dimensional reject rate from 4.1 percent to 1.8 percent.

Cleanroom conditions affect first article inspection assembly. Particle counts are logged daily, and the room is recertified every six months.

Sterilization validation for first article inspection covers three consecutive production lots. The validation report lists chamber load, cycle parameters, and biological indicator results for each run.

Defect codes for first article inspection are reviewed weekly. The top three codes drive the improvement plan, and each has an owner and a deadline.

Needle steel hardness is checked at receiving for first article inspection. A shift of 5 HV units changes penetration force, so the source is frozen at approval.

Needle steel hardness is checked at receiving for first article inspection. A shift of 5 HV units changes penetration force, so the source is frozen at approval.

Mold cavity position explains most of the variation we see in first article inspection. Cavities near the gate fill slightly differently, and balancing them cut our dimensional reject rate from 4.1 percent to 1.8 percent.

Dimensional measurement for first article inspection uses a calibrated profile projector. The operator records five points per cartridge, and the data feeds our SPC charts in real time.

We retain first article inspection samples from every lot for one year. Re-testing a retained sample answers most customer quality questions.

laboratory testing for first article inspection

Defect codes for first article inspection are reviewed weekly. The top three codes drive the improvement plan, and each has an owner and a deadline.

Dimensional measurement for first article inspection uses a calibrated profile projector. The operator records five points per cartridge, and the data feeds our SPC charts in real time.

Needle steel hardness is checked at receiving for first article inspection. A shift of 5 HV units changes penetration force, so the source is frozen at approval.

We document first article inspection defects by category every week. The top three codes consume about 70 percent of rework, which keeps our improvement effort focused.

Defect codes for first article inspection are reviewed weekly. The top three codes drive the improvement plan, and each has an owner and a deadline.

Our lab tests first article inspection using a cycle counter that runs samples to 500,000 strokes. Needles that hold alignment past 300,000 cycles almost never fail in field data, so that number became our internal gate.

Defect codes for first article inspection are reviewed weekly. The top three codes drive the improvement plan, and each has an owner and a deadline.

Defect codes for first article inspection are reviewed weekly. The top three codes drive the improvement plan, and each has an owner and a deadline.

Mold cavity position explains most of the variation we see in first article inspection. Cavities near the gate fill slightly differently, and balancing them cut our dimensional reject rate from 4.1 percent to 1.8 percent.

Adhesive cure time affects first article inspection strength. In our process, cartridges cure for 12 hours at controlled humidity, and shortening that window raised pull force failures by 1.4 percent.

Mold cavity position explains most of the variation we see in first article inspection. Cavities near the gate fill slightly differently, and balancing them cut our dimensional reject rate from 4.1 percent to 1.8 percent.

Adhesive cure time affects first article inspection strength. In our process, cartridges cure for 12 hours at controlled humidity, and shortening that window raised pull force failures by 1.4 percent.

Cleanroom conditions affect first article inspection assembly. Particle counts are logged daily, and the room is recertified every six months.

Adhesive cure time affects first article inspection strength. In our process, cartridges cure for 12 hours at controlled humidity, and shortening that window raised pull force failures by 1.4 percent.

We validate first article inspection after sterilization, not before. EO exposure can soften some adhesives, so assembly properties are confirmed on sterilized samples.

Mold cavity balance is the largest single factor in first article inspection consistency. Balancing our four cavity mold cut dimensional rejection from 4.1 percent to 1.8 percent.

Dimensional measurement for first article inspection uses a calibrated profile projector. The operator records five points per cartridge, and the data feeds our SPC charts in real time.

Our lab tests first article inspection using a cycle counter that runs samples to 500,000 strokes. Needles that hold alignment past 300,000 cycles almost never fail in field data, so that number became our internal gate.

first article inspection and quality inspection

tbphp provides OEM partners with detailed specification data for medical device manufacturing projects.

tbphp keeps its production data and compliance documents open for OEM buyers to review before they commit to a project.

Common Questions From OEM Buyers

Can I visit the factory before ordering?

Reputable suppliers welcome factory audits. Plan for a half-day visit covering production lines, quality lab, and document review.

How do payment terms work in OEM?

Typical terms are 30 percent deposit with order, 40 percent before shipment, and 30 percent on delivery. Established relationships may qualify for better terms.

What is the minimum order quantity?

MOQ varies by design complexity. Standard designs start at 1,000 units. Custom tooling projects typically require 5,000 units or more.

How do I verify a supplier claims?

Request current certification from an accredited body. Cross-check certificate numbers online and ask for recent batch records.

What happens if the product fails inspection?

production line related to first article inspection

A clear agreement should define rejection criteria. Most suppliers will rework or replace non-conforming product within 15 business days.


Leave a Reply

Your email address will not be published. Required fields are marked *